Nsi-industries DIN100 User Manual download pdf

WIRING DIAGRAM

To begin setting the unit, remove the clear

cover by lifting up from the bottom.

Insert a pin into the reset opening to clear all

memory. After a few seconds, all numbers

across the top (days of week) will flash.

TO SET CLOCK

NOTE REGARDING DAYLIGHT SAVING TIME:

A manual daylight saving time adjustment is

provided for your convenience and may be used

at your option. Inserting a pin in the DST open-

ing will advance the clock by 1 hour. A + 1h will

appear on the display. Pressing this recessed

key again will turn the clock back 1 hour to its

original setting.

If you are setting the clock during a standard

time period (NOV- MAR) set the clock for the

current time. When daylight saving arrives in

April, you can press the DST key and the clock

will advance 1 hour. A + 1h will appear on the

display. When daylight saving time is over in

October, press the DST key and the clock will

turn back 1 hour to standard time. The + 1h will

disappear from the display.

If you are setting the clock during a daylight sav-

ing time period (APR - OCT) set the clock one

hour earlier. Then press the DST key and the

clock will advance 1 hour to the correct daylight

saving time. A + 1h will appear on the display.

At the end of daylight saving time in October,

press the DST key and the clock will turn back 1

hour to standard time. The + 1h will disappear

from the display.

To set the clock you must keep Clock (CLK) key

pressed while the following settings are made:

1 - Press DAY key to set current day.

1= Monday............ 7= Sunday

2 - Press Hour (HR) key to set current hour. Be

sure to check for AM or PM. If AM or PM

does not appear, the unit is in a 24 hour

military mode. To change it to AM/PM,

insert a pin in the DST opening and press

the hour key.

12345

SPDT

TIMER

SUPPLY

CHANNEL 1

TORK DIN 100

DIGITAL TIME SWITCH

7 DAY

DIN RAIL MOUNTING

TECHNICAL DATA

Number of Channels: 1

Total number of ON and OFF events: 20

Switching Interval: 1 Minute

Manual Override: to the next scheduled event or

permanently.

Input Voltage: 120 VAC, 50/60 Hz

Power Consumption: 5 VA MAX.

Output:

Switch Configuration: SPDT (unpowered)

Switch Contact Rating: 16A Resistive

Battery Backup: 150 Hours

Battery Type: Rechargeable Ni-Cd

Operating Temperature:

14° to 140° F (-10° to 55° C)

Accuracy at 68° F: + /- 2.5 seconds/day

Dimensions: 1-7/16”w X 2-7/8”d X 3-1/4”h

Weight: 4 oz.

INSTALLATION

CAUTION:

1. INPUT WIRES TO CONTROLLER MUST

BE DEDICATED, i.e. NO OTHER LOAD

CONNECTED TO THE SAME CIRCUIT.

2. UNIT IS TO BE INSTALLED BY A

LICENSED ELECTRICIAN

DIN RAIL MOUNTING # 50022 (35 mm)

Locate red clip on back of unit and push it down.

Mount unit to DIN rail. Push red clip up from bot-

tom to lock unit onto rail. To remove from rail,

push entire unit straight up thereby forcing the

red clip down to the open position.

For surface

mounting, a small din rail is provided.

35mm

27mm

1 mm

7.5mm

6.3mm

1 2 3 4

Summary of Contents

Page 1 - DIN RAIL MOUNTING

WIRING DIAGRAMTo begin setting the unit, remove the clearcover by lifting up from the bottom.Insert a pin into the reset opening to clear allmemory. A

Page 2

WIRING DIAGRAMTo begin setting the unit, remove the clearcover by lifting up from the bottom.Insert a pin into the reset opening to clear allmemory. A

Page 3 - TO SET SCHEDULE

7 - After all settings are made, press CLK key toreturn unit to real time.NOTE: When the unit is returned to the runmode, check the load status of the

Page 4

7 - After all settings are made, press CLK key toreturn unit to real time.NOTE: When the unit is returned to the runmode, check the load status of the

Comments to this Manuals

No comments

Nsi-industries DIN100 User Manual

Browse online or download User Manual for Equipment Nsi-industries DIN100. NSi Industries DIN100 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Nsi-industries DIN100